Icharger B Pdf User Manuals. View online or download Icharger B User Manual. Read online or download PDF • Page 4 / 33 • ProgressiveRC B iCharger User Manual • ProgressiveRC Power suppliers. My iCharger B was one of the earliest released so it has firmware version where as current models are shipping with version
|Published (Last):||15 May 2004|
|PDF File Size:||10.43 Mb|
|ePub File Size:||16.95 Mb|
|Price:||Free* [*Free Regsitration Required]|
iCharger 208B Manuals
The 208 can not only measure the internal resistance of. Note that the regenerative discharge feature is shown in this newer version of the manual even though it isn’t available in my older firmware. Error messages If there is a problem during the charge an error message will be displayed.
This can be very useful if you are trying to “zoom” in on an area of the graph. Notice that the charger balanced to within 5mV, within its advertised limit. The front of the B circuit board.
You can also contact with sales hillrc. A typical result is shown in the table below.
Not to worry, there is a nice table that describes it all in detail. Ciharger picture below and to the right shows what this looks like if you just wanted to view the six cell voltages in this pack.
ProgressiveRC B iCharger User Manual | Page 4 / 33
If the balancing connector has correct polarity, and then connect the main charging port, there is no problem; but if balancing connector has reversed polarity, and then connect the main charging port, it will burn. Not only save the power but also make the charger size very smart, easy to use and convenient to take.
Return to Batteries and Chargers. When you use other equipment to charge or discharge a Lithium pack, you can use the iCharger to monitor the per-cell voltages, battery temperature and process time. Originally Posted by theShark if its W max does it really charge 10S at 10amp? Connect the manusl charging ichharger positive pole to cells’ positive pole, and then connect negative pole to cells’ negative pole this will avoid striking fire while connecting Li cells.
The iCharger B is designed and manufactured in China which in and of its self does not dictate a low quality product, but as will be shown later there is plenty of room for improvement. To test this claim I charged a 3S LiPo pack in balance mode and measured the voltage shortly after the termination of the charge. Looks and sounds like. I am told some native English speakers have helped clean it up a bit and it does show as it is a lot better than some manuals I have read eg.
If the balance tap is required to ,anual connected then the balancer is active while in the other modes the balancer is not active and connecting majual balance tap simply allows you to monitor cell voltages. Posting Quick Reply 2208b Please Wait. Files View all Files in thread. Images View all Images in thread Views: The USB connector is on the other end of the charger near the input cables. Lithium packs of cells can be charged in balanced ucharger unbalanced mode.
When you use other equipment to charge or discharge a. Battery interior resistance measurement. Oct 03, Looks like it limits LIPO up to 1C although it certainly appears to have the power ucharger charge many packs at a much higher rate. Oct 22, With the exception of the low indication of power and temperature these results are very good.
The following lists are their main specifications: Measuring power and charge with the Fluke V is not a direct process and requires the product of icharver measurements, voltage and current for power, and current and time for charge.
For this review I will be using version 3. Connection Sequence According to our engineer, the main charging port and the balance port has reversed polarity protection respectively. The PC interface is simply a USB cable which at first glance appears to be a great idea as we all have tons of them around and won’t need to store yet another specialized cable, but it turns out that this is a somewhat special USB cable so you still need to keep ichargdr of it and only use it on the iCharger.
And here is Trug ‘s blog: I actually like the specs on the iChargerB shown in that document. The back of the B circuit ichargeg. Similarly, LiFe A packs of cells can be charged in balance mode or cells in unbalanced mode.
See detail information about logview in the following website:. Where and when can those be purchased? Other features The B has built in 16Mbit flash memory that can be used to record charging data while away from a PC at the field then downloaded later when at home. For me this was my first charger with this kind of menu so I had to refer to the manual a lot and I felt like the information was very disconnected and I would often have to reference 2 or 3 sections of the manual just to figure out how to change a specific setting.
The iCharger has protection for reversed polarity input or outputlow input voltage. Another feature not seen in all chargers is a temperature probe that can be used to record pack temperature and even activate a safety shutdown if the pack gets to hot. Install the iCharger B USB driver directions for this located on the same page Run the upgrader program that came on the CD or website location given in the manual Connect the USB cable provided with the charger Select the B in the device list Click the “Open” and select the new firmware file optionally follow the directions on how to download the firmware Click “Update Basically any cell combination of most any rechargeable chemistry with a termination voltage of 36 volts or less can be charged.
In the first row we can see that the cell voltage is displayed very accurately and the pack voltage in the second row is also quite accurate. Before I show pictures of B charging plots displayed in LogView I should mention that while LogView has a English language setting, much of the German that the software writers use leaks through all over the place. Sep 05, The pricing is pretty sharp if it is for single units rather than a carton full and the chargers can live up to their specifications.